{"product_id":"borla-touring-cat-back-exhaust-system-2011-2021-jeep-grand-cherokee-140406","title":"Borla Touring Cat-Back Exhaust System for 2011-2021 Jeep Grand Cherokee 5.7L","description":"\u003cp\u003eMade for the 2011-2021 Jeep Grand Cherokee with the WK2 5.7L HEMI V8, Borla part 140406 replaces the factory exhaust from the catalytic converters back with a Touring system. It is listed for Limited, Overland or Trailhawk, 2WD or 4WD, except reusable factory tips. The tubing is 2.5\" per Borla, ending in a split rear exit with one tip on each side. It ships with 4\" round rolled angle-cut lined tips in polished stainless. Material is T-304 stainless steel. Touring is the quietest of Borla's three sound levels, by Borla's own ranking.\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eMildest of three sound levels\u003c\/strong\u003e\u003cbr\u003eBorla rates Touring as its mildest sound level, below S-Type and ATAK. Borla describes it as a mild growl, only a bit more aggressive than the factory exhaust.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStarts behind the converters\u003c\/strong\u003e\u003cbr\u003eA Cat-Back system replaces the pipes and mufflers that follow the catalytic converters. The factory converters themselves are left in place.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eT-304 austenitic stainless\u003c\/strong\u003e\u003cbr\u003eThe tubing and mufflers are T-304 austenitic stainless steel, which Borla rates well above 409 or aluminized steel for resisting rust and heat.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBuilt for one vehicle\u003c\/strong\u003e\u003cbr\u003eEach Touring system is engineered for a single platform, with the muffler layout, internals and pipe routing worked out for that vehicle and its engine.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMillion-Mile Warranty\u003c\/strong\u003e\u003cbr\u003eMaterial and workmanship defects are covered for one million miles, for the original buyer on the original vehicle. Tip finishes, coatings and moving parts carry a one-year term.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePolished stainless tips\u003c\/strong\u003e\u003cbr\u003eMost Touring systems finish in Borla's own T-304 stainless tips, polished or bright chrome, and several are also sold with black chrome or carbon fiber tips. A few systems keep the factory tips.\u003c\/p\u003e\n\u003ch3\u003eFitment \u0026amp; Compatibility\u003c\/h3\u003e\u003cstyle\u003e.pt-fit{margin:10px 0 4px;position:relative}.pt-fit\u003einput{position:absolute;width:1px;height:1px;opacity:0;margin:0;pointer-events:none}.pt-fit__tabs{display:flex;flex-wrap:wrap;gap:6px;margin:0 0 12px;padding:0}.pt-fit__tabs label{display:inline-flex;align-items:center;gap:7px;cursor:pointer;padding:6px 14px;border:1px solid #e2e4e6;border-radius:999px;background:#f2f3f4;color:#4a5057;font-weight:700;line-height:1.35}.pt-fit__tabs label\u003espan{display:inline-flex;align-items:center;justify-content:center;box-sizing:content-box;min-width:1.5em;height:1.5em;padding:0 .3em;line-height:1;font-size:.75em;font-weight:700;color:#8a9099;background:#ffffff;border-radius:999px}.pt-fit__tabs label:hover{background:#e8eaec}.pt-fit__p{display:block}#fit-140406 .pt-fit__p{display:none}.pt-fitw{overflow-x:auto;border:1px solid #e6e6e6;border-radius:8px;background:#ffffff;margin:10px 0 4px}.pt-fitw table{display:table;table-layout:fixed;width:100%;margin:0;border-collapse:separate;border-spacing:0;border:none;min-width:560px}.pt-fitw caption{caption-side:top;text-align:left;padding:0 0 8px;font-weight:700;letter-spacing:.06em;text-transform:uppercase;color:#8a9099;font-size:.8em}.pt-fit .pt-fitw caption{position:absolute;width:1px;height:1px;padding:0;overflow:hidden;clip-path:inset(50%);white-space:nowrap}@media print{.pt-fit .pt-fitw caption{position:static!important;width:auto!important;height:auto!important;clip-path:none!important;padding:0 0 8px!important}}.pt-fitw th{background:#141414;color:#ffffff;text-align:left;padding:11px 14px;font-weight:700;font-size:12px;letter-spacing:.09em;text-transform:uppercase;border:none;white-space:nowrap}.pt-fitw td{padding:11px 14px;border:none;border-bottom:1px solid #ececec;background:#ffffff;vertical-align:top}.pt-fitw tbody tr:nth-child(even) td{background:#f7f7f7}.pt-fitw tbody tr:last-child td{border-bottom:none}.pt-fitw td.y{font-weight:700;white-space:nowrap}.pt-fitw td.b{white-space:nowrap}.pt-fitw td.n{color:#5a6067;font-size:.92em}.pt-fitw td.e{color:#c4c8cc}#fit-140406\u003e.pt-fit__panels\u003e.pt-fit__p:first-of-type{display:block}#fit-140406\u003einput:checked~.pt-fit__panels\u003e.pt-fit__p{display:none}@media print{#fit-140406 .pt-fit__tabs{display:none}#fit-140406 .pt-fit__p{display:block!important}#fit-140406 .pt-fitw{overflow:visible!important}#fit-140406 .pt-fitw table{min-width:0!important}}\u003c\/style\u003e\u003cdiv class=\"pt-fitw\"\u003e\u003ctable\u003e\n\u003ccaption\u003eJeep\u003c\/caption\u003e\n\u003ccolgroup\u003e\n\u003ccol style=\"width:22%\"\u003e\n\u003ccol style=\"width:28%\"\u003e\n\u003ccol style=\"width:12%\"\u003e\n\u003ccol style=\"width:38%\"\u003e\n\u003c\/colgroup\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYears\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eBed\u003c\/th\u003e\n\u003cth\u003eNotes\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd class=\"y\"\u003e2011-2021\u003c\/td\u003e\n\u003ctd\u003eGrand Cherokee\u003c\/td\u003e\n\u003ctd class=\"b\"\u003e\u003c\/td\u003e\n\u003ctd class=\"n\"\u003eWK2 5.7L HEMI V8; Limited, Overland or Trailhawk; 2WD or 4WD; except reusable factory tips\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003c\/div\u003e\u003cdiv style=\"background:#faf7f7;border-left:4px solid #ba232a;border-radius:0 8px 8px 0;padding:14px 16px;margin:12px 0;\"\u003e\n\u003cp style=\"margin:0 0 8px;\"\u003e\u003cstrong\u003eCheck your fit:\u003c\/strong\u003e match your year, engine and cab\/bed to the fitment row: WK2 5.7L HEMI V8; Limited, Overland or Trailhawk; 2WD or 4WD; except reusable factory tips. Does not fit vehicles with reusable factory tips. Factory skid plate OK.\u003c\/p\u003e\n\u003cp style=\"margin:0;\"\u003e\u003cstrong\u003eNot for:\u003c\/strong\u003e other Touring cat-backs for this model: 140158 (2005-2010, WK 5.7L HEMI V8, single right rear exit); 14836 (1999-2004, WJ 4.0L inline-6 or 4.7L V8, single right rear exit).\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eBrand:\u003c\/b\u003e Borla\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003ePart Number:\u003c\/b\u003e 140406\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eProduct Type:\u003c\/b\u003e Cat-Back exhaust system\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eSound Level:\u003c\/b\u003e Touring (Borla's mildest level)\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eStarts At:\u003c\/b\u003e Behind the catalytic converters\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eMaterial:\u003c\/b\u003e T-304 stainless steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eTips:\u003c\/b\u003e 4\" round rolled angle-cut lined\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eLayout:\u003c\/b\u003e Split rear exit, one tip each side\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003ePipe:\u003c\/b\u003e 2.5\"\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eFinish:\u003c\/b\u003e Polished Stainless\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eUPC:\u003c\/b\u003e 808422004060\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eInstallation\u003c\/h3\u003e\n\u003cp\u003e\u003cb\u003eRecommended installation:\u003c\/b\u003e Professional · \u003cb\u003eType:\u003c\/b\u003e Hangs in place of the factory exhaust on the stock hangers on most vehicles; some sheets call for cutting the factory pipe · \u003cb\u003eTools:\u003c\/b\u003e 3\/8\" Drive Ratchet; 3\/8\" Drive Extension 3\"; 15mm Deep Well Socket; Torx socket; Pry Bar\u003c\/p\u003e\n\u003cp\u003eHere's the short version. Follow Borla's install sheet (below) for your vehicle's exact steps.\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eLubricate all hangers and rubber isolators.\u003c\/li\u003e\n\u003cli\u003eLoosen and remove nut, washer and spring on front flanges. Keep hardware for installation of your new exhaust system.\u003c\/li\u003e\n\u003cli\u003eLoosen the hardware on the left-rear muffler and carefully remove the muffler from the hangers. Repeat for the rightside rear muffler.\u003c\/li\u003e\n\u003cli\u003eWith a muffler stand or a helper holding the exhaust system in position, remove the hangers from the rubber isolators and remove the remaining exhaust system from the vehicle.\u003c\/li\u003e\n\u003cli\u003eUsing the original hardware, place the X-Pipe Muffler Assembly into position making sure to install the hangers into the rubber isolator. Hand tighten the flange making sure the original hardware is oriented as shown on the sheet.\u003c\/li\u003e\n\u003cli\u003ePlace a clamp over the expanded end of the Right-Hand Intermediate Pipe and set it into position.Do not tighten the clamp yet.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eResources\u003c\/h3\u003e\u003cul\u003e\u003cli\u003e\n\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0805\/4784\/0244\/files\/borla-install-a-35614.pdf?v=1791161441\" target=\"_blank\" rel=\"noopener\"\u003eBorla A-35614 Rev. A (PDF)\u003c\/a\u003e, Borla's own instructions for this part.\u003c\/li\u003e\u003c\/ul\u003e\n\u003ch3\u003eWarranty, Shipping \u0026amp; Returns\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWarranty.\u003c\/strong\u003e Borla's Million-Mile Warranty covers this part for one million miles against flaws in its materials or workmanship.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCoverage belongs to the original purchaser of record, on the vehicle the part was first installed on.\u003c\/li\u003e\n\u003cli\u003eBlack coatings, tip finishes, carbon fiber and moving parts such as valves and actuators carry a one-year term. Blemishes or marring caused by weather, road hazards, lack of maintenance or extreme heat or cold are not covered.\u003c\/li\u003e\n\u003cli\u003eBorla inspects the returned part, and when it finds a manufacturing or material defect it repairs or replaces the part, at Borla's option.\u003c\/li\u003e\n\u003cli\u003eSound level is not warranted, since sound is a matter of taste. Borla notes that venturis can be fitted to quiet a system.\u003c\/li\u003e\n\u003cli\u003eUniversal mufflers must be joined at their inlet and outlet necks. Welding to the case shell or end caps voids the warranty.\u003c\/li\u003e\n\u003cli\u003eNot covered: the cost of removal or reinstallation; damage from accident, abuse, misuse or misapplication; parts that are modified or used for something other than their intended purpose; racing products, and street parts used for racing.\u003c\/li\u003e\n\u003cli\u003eTo claim, contact us first with your order number and a short description of the problem. Borla asks for proof of the retail purchase date, and your Prestige Truck receipt is that proof. A part sent back to Borla travels with freight prepaid by the sender, packed well, since Borla cannot accept parts damaged in transit.\u003c\/li\u003e\n\u003cli\u003eSome states do not allow these limits, so your rights may vary by state.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eFree shipping.\u003c\/strong\u003e Ships free to the lower 48 states, with no minimum order.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eOrder by 5 PM ET on a business day and it starts processing the same day.\u003c\/li\u003e\n\u003cli\u003eMost orders arrive within 1-5 business days.\u003c\/li\u003e\n\u003cli\u003eWe email your tracking number as soon as it ships.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eInspect on delivery.\u003c\/strong\u003e This system ships in a large carton: lay every pipe, muffler, clamp and hanger out against the install sheet's parts list before you start, and photograph any dents or scuffed tips right away. Check it as soon as it arrives.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eLook for crushed ends, punctures or tears in the carton.\u003c\/li\u003e\n\u003cli\u003eIf something looks wrong, take photos of the box and the parts (and if a driver asks you to sign, note the damage on the receipt).\u003c\/li\u003e\n\u003cli\u003eOpen the box and check the parts against the parts list before you install.\u003c\/li\u003e\n\u003cli\u003eEmail \u003ca href=\"mailto:support@prestigetruck.com\"\u003esupport@prestigetruck.com\u003c\/a\u003e right away with your order number, a short note and photos. We send a replacement or a full refund at no cost to you.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003e30-day returns.\u003c\/strong\u003e Return it within 30 days of delivery, unused, in the original packaging, with proof of purchase.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eEmail \u003ca href=\"mailto:support@prestigetruck.com\"\u003esupport@prestigetruck.com\u003c\/a\u003e with your order number. We reply within 1-2 business days with instructions.\u003c\/li\u003e\n\u003cli\u003eDamaged, defective or wrong item: we send a prepaid label or arrange a pickup.\u003c\/li\u003e\n\u003cli\u003eChanged your mind: you pay return shipping. No restocking fee.\u003c\/li\u003e\n\u003cli\u003eRefunds go back to your original payment method within 7 business days of approval. See our \u003ca href=\"https:\/\/prestigetruck.com\/policies\/refund-policy\"\u003ereturns policy\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eAbout Borla\u003c\/h3\u003e\n\u003cdiv style=\"display:flex;flex-wrap:wrap;gap:24px;align-items:flex-start;margin:6px 0 4px;\"\u003e\n\u003cdiv style=\"flex:0 0 150px;max-width:150px;border:2px solid #14161a;padding:12px 8px;text-align:center;font:700 22px\/1.1 Rajdhani,'Arial Narrow',sans-serif;letter-spacing:.06em;color:#14161a;\"\u003eBORLA\u003cspan style=\"color:#ba232a;\"\u003e.\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv style=\"flex:1 1 340px;min-width:240px;\"\u003e\n\u003cp\u003eBorla got its start in 1978 making stainless exhaust systems for concours Rolls-Royce and Ferrari restorations, and says the term Cat-Back began with it that same year. The company still builds in stainless steel, now at a 100-acre plant in Tennessee, and Borla says automakers including GM, Ford and Toyota use it for some of their factory-installed accessory exhaust.\u003c\/p\u003e\n\u003cp\u003eBorla engineers each vehicle system from a clean sheet, shaping the muffler bodies, cores and pipe routing around that one platform, and offers many of its systems in three sound levels: Touring, S-Type and ATAK. For custom work it makes ProXS universal mufflers, CrateMufflers tuned to crate engines, exhaust tips, tubing, clamps and hangers.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv style=\"background:#faf7f7;border-left:4px solid #ba232a;border-radius:0 8px 8px 0;padding:14px 16px;margin:16px 0 0;\"\u003e\u003cp style=\"margin:0;\"\u003e\u003cstrong\u003eAuthorized Borla dealer.\u003c\/strong\u003e Prestige Truck is an authorized Borla dealer, so every Borla part we sell is new and genuine. Borla's Million-Mile Warranty is for the original purchaser, on the vehicle the part was first installed on. Keep your Prestige Truck order receipt: Borla asks for proof of the purchase date with any claim, and we use it when we take a claim to Borla for you.\u003c\/p\u003e\u003c\/div\u003e","brand":"Borla","offers":[{"title":"Default Title","offer_id":67697622221044,"sku":"140406","price":1799.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0805\/4784\/0244\/files\/borla-borla-touring-cat-back-exhaust-system-studio-layout-of-a-dual-exit-stainless-cat-back-1_111d1713-6d1b-4f0e-8b94-5d7792caea38.jpg?v=1791164279","url":"https:\/\/prestigetruck.com\/products\/borla-touring-cat-back-exhaust-system-2011-2021-jeep-grand-cherokee-140406","provider":"Prestige Truck","version":"1.0","type":"link"}