{"product_id":"teraflex-high-angle-rzeppa-cv-joint-replacement-kit-2018-2026-jeep-wrangler-gladiator-1745000","title":"TeraFlex High-Angle Rzeppa CV Joint Replacement Kit for 2018-2026 Jeep Wrangler\/Gladiator","description":"\u003cp\u003eThe High-Angle Rzeppa CV Joint Replacement Kit is a TeraFlex driveline part aimed at a specific wear point or angle problem on a lifted, hard-used rig. It lets you fix or improve one part of the driveline without replacing the whole assembly. Part number 1745000 is listed for the 2018-2026 Jeep Wrangler and Gladiator.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat's Included:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eRzeppa CV joint\u003c\/li\u003e\n\u003cli\u003eInstallation tool\u003c\/li\u003e\n\u003cli\u003eHigh-viscosity, surface-bonding, low-friction grease\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eNot Included:\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eDriveshafts, axle shafts, axle housings, gear oil and installation labor are not included unless the listing names them.\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eTargets one driveline wear point\u003c\/strong\u003e\u003cbr\u003eEach part in this collection replaces or improves a single component, so you can repair the piece that needs attention instead of buying a complete assembly.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMade for lifted Jeep angles\u003c\/strong\u003e\u003cbr\u003eThese parts are developed with lifted suspensions in mind, where steeper driveline angles and longer travel put extra stress on joints, hubs and mounts.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHardware and instructions from TeraFlex\u003c\/strong\u003e\u003cbr\u003eEach kit ships with the TeraFlex parts it lists, and installation guides are linked on the product pages where TeraFlex publishes them.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHome garage friendly jobs\u003c\/strong\u003e\u003cbr\u003eThese are bolt-on service jobs that a capable home mechanic can handle with hand tools and a torque wrench, though TeraFlex recommends a certified mechanic.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBacked by TeraFlex support\u003c\/strong\u003e\u003cbr\u003eTeraFlex has been building Jeep axle and driveline parts for decades, and its customer service team supports every part it sells.\u003c\/p\u003e\n\u003ch3\u003eFitment \u0026amp; Compatibility\u003c\/h3\u003e\u003cstyle\u003e.pt-fit{margin:10px 0 4px;position:relative}.pt-fit\u003einput{position:absolute;width:1px;height:1px;opacity:0;margin:0;pointer-events:none}.pt-fit__tabs{display:flex;flex-wrap:wrap;gap:6px;margin:0 0 12px;padding:0}.pt-fit__tabs label{display:inline-flex;align-items:center;gap:7px;cursor:pointer;padding:6px 14px;border:1px solid #e2e4e6;border-radius:999px;background:#f2f3f4;color:#4a5057;font-weight:700;line-height:1.35}.pt-fit__tabs label\u003espan{display:inline-flex;align-items:center;justify-content:center;box-sizing:content-box;min-width:1.5em;height:1.5em;padding:0 .3em;line-height:1;font-size:.75em;font-weight:700;color:#8a9099;background:#ffffff;border-radius:999px}.pt-fit__tabs label:hover{background:#e8eaec}.pt-fit__p{display:block}#tfx-1745000 .pt-fit__p{display:none}.pt-fitw{overflow-x:auto;border:1px solid #e6e6e6;border-radius:8px;background:#ffffff;margin:10px 0 4px}.pt-fitw table{display:table;table-layout:fixed;width:100%;margin:0;border-collapse:separate;border-spacing:0;border:none;min-width:560px}.pt-fitw caption{caption-side:top;text-align:left;padding:0 0 8px;font-weight:700;letter-spacing:.06em;text-transform:uppercase;color:#8a9099;font-size:.8em}.pt-fit .pt-fitw caption{position:absolute;width:1px;height:1px;padding:0;overflow:hidden;clip-path:inset(50%);white-space:nowrap}@media print{.pt-fit .pt-fitw caption{position:static!important;width:auto!important;height:auto!important;clip-path:none!important;padding:0 0 8px!important}}.pt-fitw th{background:#141414;color:#ffffff;text-align:left;padding:11px 14px;font-weight:700;font-size:12px;letter-spacing:.09em;text-transform:uppercase;border:none;white-space:nowrap}.pt-fitw td{padding:11px 14px;border:none;border-bottom:1px solid #ececec;background:#ffffff;vertical-align:top}.pt-fitw tbody tr:nth-child(even) td{background:#f7f7f7}.pt-fitw tbody tr:last-child td{border-bottom:none}.pt-fitw td.y{font-weight:700;white-space:nowrap}.pt-fitw td.b{white-space:nowrap}.pt-fitw td.n{color:#5a6067;font-size:.92em}.pt-fitw td.e{color:#c4c8cc}#tfx-1745000\u003e.pt-fit__panels\u003e.pt-fit__p:first-of-type{display:block}#tfx-1745000\u003einput:checked~.pt-fit__panels\u003e.pt-fit__p{display:none}@media print{#tfx-1745000 .pt-fit__tabs{display:none}#tfx-1745000 .pt-fit__p{display:block!important}#tfx-1745000 .pt-fitw{overflow:visible!important}#tfx-1745000 .pt-fitw table{min-width:0!important}}\u003c\/style\u003e\u003cdiv class=\"pt-fitw\"\u003e\u003ctable\u003e\n\u003ccaption\u003eJeep\u003c\/caption\u003e\n\u003ccolgroup\u003e\n\u003ccol style=\"width:22%\"\u003e\n\u003ccol style=\"width:38%\"\u003e\n\u003ccol style=\"width:40%\"\u003e\n\u003c\/colgroup\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYears\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eNotes\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd class=\"y\"\u003e2018-2026\u003c\/td\u003e\n\u003ctd\u003eWrangler\u003c\/td\u003e\n\u003ctd class=\"n\"\u003eJL\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd class=\"y\"\u003e2020-2026\u003c\/td\u003e\n\u003ctd\u003eGladiator\u003c\/td\u003e\n\u003ctd class=\"n\"\u003eJT\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003c\/div\u003e\u003cdiv style=\"background:#faf7f7;border-left:4px solid #ba232a;border-radius:0 8px 8px 0;padding:14px 16px;margin:12px 0;\"\u003e\u003cp style=\"margin:0;\"\u003e\u003cstrong\u003eFit guidance:\u003c\/strong\u003e Fits: 2018-2026 Jeep Wrangler\/Gladiator (JL; JT). Not for the rear driveshaft on 2026 JL\/JT; fits the 2026 front driveshaft and 2018-2025 front and rear. Check your trim and factory equipment against the notes before ordering.\u003c\/p\u003e\u003c\/div\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eBrand:\u003c\/b\u003e TeraFlex\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eCountry of origin:\u003c\/b\u003e Taiwan\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eNot for:\u003c\/b\u003e 2026 JL\/JT rear driveshaft\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003ePart number:\u003c\/b\u003e 1745000\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eType: Driveline and axle-end service parts  ·  Install: Bolt-on, hand tools and a torque wrench  ·  Afterward: Recheck fasteners after the first miles\u003c\/p\u003e\u003cp\u003eRead the TeraFlex instructions for this part completely before starting, and use the factory service manual alongside them. A certified mechanic is recommended. Recheck all fasteners after the first miles of driving.\u003c\/p\u003e\u003cp\u003eCovers replacing the factory Rzeppa CV joint on the driveshaft: the driveshaft comes out, the old joint, boot clamp and snap ring come off, and the new bearing assembly is packed completely with the supplied grease before it goes in. TeraFlex stresses that this is the only chance to grease the joint, and a 6mm hex tool is included for the flange bolts.\u003cbr\u003e\u003cb\u003eTools named in the guide:\u003c\/b\u003e General mechanics tools, Torque wrench, 3-jaw puller (optional), Snap ring pliers, T-50 Torx, Supplied 6mm hex tool\u003cbr\u003e\u003cb\u003eTorque:\u003c\/b\u003e 29 ft-lb, CV joint bolts, tightened with the supplied 6mm hex tool and blue thread locker; 89 ft-lb, 15mm driveshaft bolts on reinstallation\u003c\/p\u003e\u003cp\u003eTeraFlex's installation instructions for this part number are linked under Resources. Read them fully before starting.\u003c\/p\u003e\u003cdiv style=\"position:relative;padding-bottom:56.25%;height:0;overflow:hidden;margin:12px 0;\"\u003e\u003ciframe src=\"https:\/\/www.youtube-nocookie.com\/embed\/VNT05gjgO8g\" title=\"TeraFlex installation video\" style=\"position:absolute;top:0;left:0;width:100%;height:100%;border:0;\" loading=\"lazy\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/div\u003e\n\u003ch3\u003eResources\u003c\/h3\u003e\u003cul\u003e\u003cli\u003e\n\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0805\/4784\/0244\/files\/teraflex-install-1836-999452-jljt-high-angle-rzeppa-cv-joint.pdf?v=1790627314\" target=\"_blank\" rel=\"noopener\" title=\"TeraFlex Rzeppa CV joint installation instructions (PDF)\" style=\"color:#ba232a;font-weight:700;text-decoration:underline;\"\u003eTeraFlex Rzeppa CV joint installation instructions (PDF)\u003c\/a\u003e, TeraFlex's step-by-step guide.\u003c\/li\u003e\u003c\/ul\u003e\n\u003ch3\u003eWarranty, Shipping \u0026amp; Returns\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWarranty.\u003c\/strong\u003e TeraFlex backs its products with a limited warranty against defects in materials and workmanship for the original purchaser, on the vehicle the part was first installed on. Axle shafts, Rzeppa CV kits, yokes and driveshaft components are covered for 1 year. If a covered part fails, TeraFlex will repair or replace it or refund the purchase price at its discretion. The warranty does not cover improper installation, missed maintenance, modifications, normal wear, finish wear or racing and competition use, and paint and powder coat finishes are covered for 90 days against defects only. \u003cstrong\u003eShipping.\u003c\/strong\u003e The carrier and ship method are set by the size and weight of the cartons when the order is placed; larger kits and axles ship by freight. \u003cstrong\u003eInspect on delivery.\u003c\/strong\u003e Inspect the carton and every part as soon as the delivery arrives, note any shipping damage with the carrier, and contact us right away so we can make it right. \u003cstrong\u003eReturns.\u003c\/strong\u003e Replacement parts are final sale unless defective.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReturns.\u003c\/strong\u003e Unused items in their original packaging can be returned within 30 days of delivery. If an item arrives damaged, defective or wrong, return shipping is on us. See our \u003ca href=\"https:\/\/prestigetruck.com\/policies\/refund-policy\"\u003eReturns \u0026amp; Refunds Policy\u003c\/a\u003e, or email \u003ca href=\"mailto:support@prestigetruck.com\"\u003esupport@prestigetruck.com\u003c\/a\u003e with any question.\u003c\/p\u003e\n\u003ch3\u003eAbout TeraFlex\u003c\/h3\u003e\u003cdiv class=\"pt-about\" style=\"margin:6px 0 4px;\"\u003e\n\u003cp\u003eTeraFlex is a Jeep company at heart, started and staffed by people who drive them. It designs, engineers and builds suspension systems, shocks, axles and performance parts, with the Wrangler and Gladiator at the center of the lineup.\u003c\/p\u003e\n\u003cp\u003eThe company traces its history to the 1950s, when it began as MEPCO (Military Equipment Parts Company), one of the first companies anywhere to supply Jeep parts and accessories. TeraFlex Manufacturing followed in 1996 to build heavy-duty suspension for the TJ Wrangler, and the brand credits itself with the first suspension system for that coil-spring platform, a low-range gearing option for the 231 transfer case and the CRD60 high-pinion axle.\u003c\/p\u003e\n\u003cp\u003eThe current catalog covers full lift systems, the Falcon shock line and a long list of Wrangler and Gladiator upgrades, and the company is now carrying the same engineering approach to other vehicles as well.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"TeraFlex","offers":[{"title":"Default Title","offer_id":67602156159220,"sku":"1745000","price":208.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0805\/4784\/0244\/files\/teraflex-driveline-component-brass-finish-cv-joint-with-hex-driver-bit-1.jpg?v=1790687184","url":"https:\/\/prestigetruck.com\/products\/teraflex-high-angle-rzeppa-cv-joint-replacement-kit-2018-2026-jeep-wrangler-gladiator-1745000","provider":"Prestige Truck","version":"1.0","type":"link"}