This Go Rhino Dominator D1 listing covers the 2024-2026 Toyota Tacoma. The heavy-duty steel frame also sits between the rocker panel and rocks or debris thrown up by the tires. It is finished in textured black under Go Rhino part number D14432T.
What's Included:
- Driver and passenger side Dominator D1 side steps
- Dominator Xtreme mounting bracket kit with hardware for this application
- Vehicle-specific Go Rhino installation guide
Tools are not included; the guide for your part number lists them, and a few applications also call for a drill.
Features
5.5" Full-Width Step
The step surface is 5.5" wide and runs the length of the cab, so there is room for a whole boot at every door.
Hex-Pattern Dimpled Tread
Plate-steel step tread is dimpled with a raised hexagonal pattern that bites into boot soles in rain, mud or snow.
Tubular Steel Frame
A heavy-duty tubular steel structure carries the tread, and plate-steel accents add stiffness so the step feels solid underfoot.
Rocker Panel Protection
Mounted along the rockers, the all-steel steps take hits from rocks and road debris that would otherwise chip the paint.
Textured Black Powder Coat
A heavy-duty textured black powder coat guards the steel against chips, scratches, fading and corrosion.
Dominator Xtreme Mount Kit
Each pair includes a mount kit and install guide for its vehicle, and most applications bolt on without drilling.
Fitment & Compatibility
Fit guidance: Fits the 2024-2026 Toyota Tacoma, with the cab and equipment notes shown in the table.
Cab and equipment: Double Cab
Specifications
-
Brand: Go Rhino
-
Series: Dominator D1
-
Step width: 5.5"
-
Length: Cab length
-
Construction: Tubular steel frame with dimpled plate-steel step tread
-
Material: Mild steel
-
Tread: Raised hexagonal pattern
-
Mounting: Rocker panel, Dominator Xtreme mount kit
-
Warranty: Limited lifetime structural, 5 years on finish
-
Mount Location: Mounts to Rocker Panel
-
Finish: Textured Black
-
Part number: D14432T
Installation
Type: Bolt-on · Mount: rocker panel, Dominator Xtreme mount kit · Drilling: none on most applications; some call for drilling or enlarging holes (the guide for each part number says)
The Go Rhino guides for this part number, linked below, show the bracket locations, hardware and tools for this vehicle, including any drilling it calls for. Mount the brackets, set the steps with their nut-plates, then align and tighten.
Resources
Warranty, Shipping & Returns
Warranty. Go Rhino's limited lifetime structural warranty covers manufacturing defects in materials or workmanship for as long as the product lasts, provided it was installed per Go Rhino's instructions. A limited 5-year finish warranty, for the original owner, covers red rust, peeling, flaking and cracking from the date of purchase. Go Rhino may ask for proof of purchase and photos of the defect, repairs or replaces a covered part at its discretion, and needs an RGA number on every warranty return; shipping on a finish claim is the owner's cost.
Shipping. Ships by ground carrier. The steps travel in a long carton, and the steps and the Dominator mounting bracket kit may arrive as separate boxes.
Inspect on delivery. Open every carton when it arrives and check both steps, the bracket kit and the hardware against the parts list in the Go Rhino guide before you start. Note any visible carton damage on the delivery receipt and photograph it, because damage reported later is much harder to claim.
Returns. Unused items in their original packaging can be returned within 30 days of delivery. If an item arrives damaged, defective or wrong, return shipping is on us. See our Returns & Refunds Policy, or email support@prestigetruck.com with any question.
About Go Rhino
Go Rhino makes exterior accessories for pickups, Jeeps and SUVs. Along the sides of the vehicle the range covers running boards in the RB10, RB20 and RB30 lines and their Slim versions, VoltStep electric running boards (power boards), nerf bars and side steps such as the 1000 Series, 4000 Series and O.E. Xtreme, V-Series V3 steps, and the Dominator steps, drop steps and DSS sliders, along with frame-mounted rock sliders. At the front, Go Rhino builds the Charger RC2 and RC4 LR bull bars, the 3000 Series grille guard and 3100 Series StepGuard, and front bumpers including the BR11, Element, Trailline and Rockline.
Further back come rear bumpers such as the BR20.5 and Trailline, sport bars and bed bars, stake pocket bed rails, XRS bed racks and cross bars, and the CEROS roof rack, plus light mounts for the hood, windshield and cowl, jack mounts and a spare tire relocation kit for Jeeps. Many Go Rhino products carry a limited lifetime structural warranty together with a 5-year finish warranty; other lines are covered for 5 years on black finishes and for the life of the product on polished stainless, and the frame-mounted sliders carry a 1-year warranty. Go Rhino is based in Brea, California.
