N-Fab Roan Running Boards for 2019-2026 Chevrolet Silverado / GMC Sierra 1500, 2020-2026 Chevrolet Silverado / GMC Sierra 2500 HD / 3500 HD (Crew Cab)

The Roan is a cab-length steel running board: a tubular steel frame carrying a 5.5" wide, stitch-welded 12-gauge step plate with removable raised-louver tread plates, on an adjustable rocker-panel bracket system. On the 2019-2026 Chevrolet Silverado / GMC Sierra 1500, 2020-2026 Chevrolet Silverado / GMC Sierra 2500 HD / 3500 HD crew cab, the Roan puts a 5.5" wide steel step below every door, backed by N-Fab's 475 lb weight capacity. This listing is N-Fab part number NBC19CC, finished in textured black.

What's Included:

• 2x Roan running boards (driver and passenger side)
• Removable louvered tread plates
• Vehicle-specific rocker panel brackets
• Mounting hardware kit

Features

475 lb Weight Capacity
N-Fab rates the Roan at a 475 lb weight capacity. The strength comes from a tubular steel frame under a plate-steel step rather than a single bent tube.

A 5.5" Steel Plate Step
The step is 12-gauge steel plate, 5.5" wide, stitch-welded to the frame. Stitch welding joins the plate in short runs, which adds strength while keeping heat distortion out of the flat surface.

Raised Louver Tread
The top of the step carries raised louvers that give a boot an edge to grip in wet or muddy conditions.

Removable Tread Plates
The tread plates bolt on rather than being welded, so they can come off to be refinished or colored to suit your build.

Adjustable Mounting System
The brackets allow the board to be positioned during install, so you can set it where it suits your vehicle and your stride before tightening everything down.

Bolt-On, No Drilling
The vehicle-specific brackets line up with existing holes in the rocker panel, and every Roan application installs with the supplied hardware and no drilling.

Textured Black Powder Coat
The steel is sealed in a textured black powder coat that resists scratches, chips, oil and chemicals. N-Fab warrants the finish for five years.

Fitment & Compatibility

Specifications

• Series: N-Fab Roan
• Product Type: Cab-length running boards
• Material: Tubular steel frame, 12-gauge steel step plate
• Step Width: 5.5"
• Step Surface: Raised louver, removable tread plates
• Weight Capacity: 475 lb
• Mounting: Adjustable brackets at the rocker panel, no drilling
• Sold As: A pair, driver and passenger side
• Part number: NBC19CC-TX
• Finish: Textured Black
• Warranty: Lifetime structural + 5-year powder-coat finish

Installation

Type: Bolt-on, no drilling  ·  Tools: Hand tools (socket set, ratchet and a torque wrench)  ·  Difficulty: DIY-friendly; a helper makes lifting the boards easier

The vehicle-specific brackets bolt to existing holes in the rocker panel, then the boards are set on the brackets and positioned before the hardware is brought up to torque. Take the time to get both sides level and even before the final tightening, and check the bolts again after the first few hundred miles. The installation guide for this application uses the factory mounting points and does not call for drilling.

Resources

• Official N-Fab Roan installation guide (PDF), the manufacturer's step-by-step installation instructions for this part number.

Warranty, Shipping & Returns

Warranty. N-Fab warrants the Roan running boards for life against defects in materials and workmanship, covering the frame, the step plates, the brackets and the welds, and warrants the powder-coat finish for five years. Both terms belong to the original purchaser, on the vehicle the product was first installed on, and they do not transfer if the vehicle is sold.

Free shipping. This part ships by ground carrier as an oversize parcel, in a long carton rather than on a pallet.

Inspect on delivery. A long carton takes knocks in transit, so look it over while the driver is there and note any crushed ends or punctures on the delivery record. Unpack it the same day and check the parts list: a bent bracket or a short hardware bag reported in the first days is a quick replacement.

Returns. Unused items in their original packaging can be returned within 30 days of delivery. N-Fab charges a 20% restocking fee on any product returned without a defect, and an N-Fab representative has to confirm a defect in fit, form or function before a return is authorized, so please contact us before shipping a part back. If an item arrives damaged, defective or wrong, return shipping is on us. See our Returns & Refunds Policy, or email support@prestigetruck.com with any question.

About N-Fab