LOMAX Stance Hard Tri-Fold Tonneau Cover

Built around extruded aluminum panels finished in textured urethane, the LOMAX Stance is a hard tri-fold cover that reads more like a spray in liner than a sheet of metal. The panels join with reinforced vinyl coated hinges that shed water off the sides. Pull the nylon cord under the rear panel to release the latches, then fold the cover forward. Stop at the two thirds position for everyday loads or take it all the way to the cab when the bed has to be wide open. Rated to 400 lb evenly spread.

What's Included:

• Tri-fold cover with extruded aluminum panels
• Textured urethane top surface in the pattern you select
• Reinforced vinyl coated hinges fitted between the panels
• Driver and passenger mounting rails
• Clamps and mounting hardware
• Nylon release cords and installation instructions

Features

Urethane over extruded aluminum
The panels start as extruded aluminum, then take a textured urethane skin close in feel to a spray in bedliner. That layer is both the look of the cover and an extra layer of protection over the metal.

Three top patterns to pick
Stance covers are ordered in one of three urethane finishes. Aluminum, diamond plate or carbon fiber, so you can match the cover to the truck rather than take whatever the line happens to offer.

Pull cord, fold forward
A nylon cord tucked under the cover releases the rear panel latches. It can be pulled from either side of the bed, which helps when the truck is parked tight against a wall or another vehicle.

Flat against the cab
Large loads do not mean pulling the cover off. Fold all three panels up against the cab, latch them there and haul what you need. If you would rather keep some coverage, the two thirds position locks in as well.

Ten locking points when shut
Closed, the Stance engages at ten points along the rails. That keeps cargo out of sight and keeps the panels tight to the bed rather than held by a single latch at the tailgate.

Hinges that move water out
The vinyl coated hinges between the panels are sealed, so water running down the cover is steered toward the rails instead of through the seams. The cover overlaps the bed rails to carry that seal the full length of the bed.

Fitment & Compatibility

Specifications

• Cover Type: Hard tri-fold, folding
• Material: Extruded aluminum panels with a textured urethane top
• Finish: Urethane in aluminum, diamond plate or carbon fiber
• Profile: Half an inch above the bed rails
• Bed Access: Two thirds position or folded flat against the cab
• Weight Capacity: 400 lb evenly distributed
• Sealing: Reinforced vinyl coated hinges and perimeter seals
• Security: Ten locking points when closed
• Drilling Required: None on most beds, CarbonPro beds bolt on
• Rack Compatible: Not stated
• Fits: See the fitment table and the vehicle selector
• Made In: USA
• Warranty: Three year limited warranty

Installation

Type: Rail mounted, clamp on for most beds · Time: Not stated by the manufacturer · Tools: Included hardware and basic hand tools · Difficulty: Moderate, a second person helps with the panels

The Stance mounts on rails that run down each bed rail, and the cover sits on top of them. Most beds clamp on with the supplied hardware. The exception is called out in the fitment options, where Silverado and Sierra beds with the CarbonPro liner take a bolt on install. Read the sheet in the box before setting the rails, since the cover has to sit square to seal.

Watch the installation walkthrough:

Warranty, Shipping & Returns

Warranty. The Stance is covered by a three year limited warranty on workmanship, counted from the date the cover was made and tied to normal use on the truck model it was built for. Damage from accidents, misuse, alteration, neglect or a poor install falls outside it, as does ordinary wear. Repair or replacement of the defective part is the remedy, and labor is not included.

Free shipping. This item ships free to the lower 48 states. Because it is an oversized item, it ships by freight or oversized parcel and typically arrives in 3 to 7 business days.

Inspect on delivery. Please inspect the packaging before signing. If you see any damage, note it on the delivery receipt and contact us right away, and we will make it right.

Returns. Unused items in their original packaging can be returned within 30 days of delivery. If an item arrives damaged, defective or wrong, return shipping is on us. See our Returns & Refunds Policy, or email support@prestigetruck.com with any question.

About LOMAX

LOMAX makes tri-fold hard covers for pickups. Three lines share the name. The Folding Hard Cover, the Professional Series and the Stance all fold in thirds rather than rolling into a canister or retracting on rails. Production is in the United States.

What separates the Stance from the rest of the LOMAX range is the top surface. Instead of leaving the aluminum bare or in a plain powder coat, the maker skins it in textured urethane and offers that skin in three patterns. The frame underneath is still extruded aluminum.

Coverage runs from half ton pickups through heavy duty Ford, Ram, Chevrolet and GMC beds. Midsize trucks are in the list too, including the Colorado, Canyon, Frontier, Tacoma and Santa Cruz. Whichever one you drive, the same three year limited warranty on workmanship applies.