BAKFlip G2 Hard Folding Tonneau Cover for 2024-2026 Toyota Tacoma (5' Bed)

The all-new 2024-2025 Toyota Tacoma gets a fresh-fit BAKFlip G2, cut for the redesigned 5' (60") short bed. Fold the solid-core panels for full access, or close the low semi-gloss black cover for weather-resistant, tailgate-locked security on your fourth-generation Tacoma. Rated to 300 lb, no-drill clamp-on install.

What's Included:

• BAKFlip G2 hard folding tonneau cover assembly (pre-assembled panels)
• Driver and passenger side mounting rails with integrated clamps
• Clamp-on mounting hardware for a no-drill install
• Front and tailgate weather seals
• Integrated water drainage tubes
• BAKFlip G2 installation guide

Features

Full 100% Bed Access, Folds Against the Cab
The solid-core panels fold forward and stack flush against the cab in seconds, opening the entire bed for a refrigerator, dirt bike, or a stack of lumber. An integrated buckle system also lets you drive with the cover closed, folded two-thirds back, or flipped fully up, so you choose how much bed you need on any given day.

Solid-Core Panels With Aircraft-Grade Aluminum Skins
Each fold-flat panel pairs a durable solid core with an aircraft-grade aluminum skin, giving the G2 a rigid, secure deck rated to hold up to 300 lb of evenly distributed weight while staying light enough to fold with one hand.

Semi-Gloss Black, Built to Shrug Off UV
The low-profile cover wears a corrosion-resistant semi-gloss black finish with premium UV resistance, so it will not fade or chalk after seasons of sun. It sits low and tight to the bed rails for a clean factory look.

Weather-Resistant Seals and Integrated Drainage
Precision-fit EPDM rubber perimeter seals close the gap between the cover and the bed rails, and an integrated drainage system channels the water that reaches the seams down and out through drain tubes, away from your cargo. It is built to keep rain and car-wash spray off your gear.

Locks Down With Your Tailgate
The patented rail-and-clamp system uses automatic slam latches that grab as you lower each panel, and the latches sit concealed under the closed cover. Lock your tailgate and the bed is secured, with no exposed hardware to pry.

No-Drill Clamp-On Install in About 30 Minutes
The G2 clamps onto your factory bed rails with the included hardware, no cutting, trimming, or drilling. Most installs take about 30 minutes with basic hand tools, and the cover is compatible with the BAKBox 2 tonneau toolbox if you want lockable in-bed storage.

Fitment & Compatibility

Specifications

• Cover Type: BAKFlip G2 hard folding (tri-fold) tonneau cover
• Panel Construction: Durable solid-core panels with aircraft-grade aluminum skins
• Finish: Semi-gloss black, corrosion-resistant, UV-stable (will not fade or chalk)
• Bed Access: 100%, panels fold flat against the cab; drive closed, folded, or flipped up
• Weight Capacity: Up to 300 lb evenly distributed on the closed cover
• Weather Sealing: Precision-fit EPDM perimeter seals with an integrated water drainage system
• Security: Patented rail-and-clamp system, automatic slam latches, locks with the tailgate
• Third Brake Light: Retains third brake light visibility (short and standard beds)
• Drilling Required: No, clamp-on install on the factory bed rails
• Install Time: About 30 minutes with basic hand tools
• Accessory Compatible: BAKBox 2 tonneau toolbox
• Warranty: 3-year limited
• Assembled In: USA
• Shipping Weight: About 71 lb

Installation

Type: Clamp-on, no drilling  ·  Time: About 30 minutes  ·  Tools: Basic hand tools; no drill required with the included clamps  ·  Difficulty: Easy, one person

Set the two rails on your factory bed rails, position the pre-assembled cover, and tighten the included clamps. No cutting, trimming, or drilling into the truck. Watch the BAKFlip G2 installation video in this tab and follow the printed BAKFlip G2 install guide for exact clamp placement.

Watch the model-specific installation walkthrough:

Resources

Everything you need for your BAKFlip G2 Hard Folding Tonneau Cover for 2024-2026 Toyota Tacoma, in one place.

• Official BAKFlip G2 Hard Folding Tonneau Cover for 2024-2026 Toyota Tacoma installation guide (PDF), the manufacturer's step-by-step guide covering mounting, included hardware and adjustment.

Warranty, Shipping & Returns

Warranty. 3-Year Limited Warranty from BAK against defects in materials and workmanship, backed by US-based support. It does not cover accident damage, misuse, or improper installation.

Free shipping. This item ships free to the lower 48 states. Because it is an oversized item, it ships by freight and typically arrives in 3 to 7 business days.

Inspect on delivery. Please inspect the packaging before signing. If you see any damage, note it on the delivery receipt and contact us right away, and we will make it right.

About BAK Industries

BAK Industries has engineered premium truck bed covers in the USA for decades and is a flagship tonneau brand of RealTruck, one of the largest truck-accessory manufacturers in North America. Its hard-folding BAKFlip and retractable Revolver lines set the benchmark for the category, pairing heavy-duty aluminum construction with a low-profile, weathertight design.

Every BAK cover is built for real-world truck use: no-drill, clamp-on installation that mounts in about 30 minutes, full bed access when folded or rolled back, and reinforced latching that keeps cargo secure and dry. The lineup runs from the value-focused BAKFlip MX4 and G2, to the flagship FRP-panel F1 and FiberMax, to the industrial Revolver X2 and X4s roll-ups, covering nearly every popular truck and bed length.

Backed by US-based product support and a multi-year manufacturer warranty, a BAK cover is a buy-it-once upgrade that protects tools, cargo, and gear while giving a truck a cleaner, more finished look.