Extang Solid Fold Toolbox 2.0 Hard Folding Tonneau Cover for 2015-2022 Chevrolet Colorado / GMC Canyon (6'2" Bed)
Free gifts included with your order
- Guaranteed FitmentTeam-confirmed fit or money back
- No Sales TaxZero sales tax on every order
- 30-Day Money-Back GuaranteeReturn it within 30 days of delivery for a refund
Questions or a custom quote?
Mon to Fri, 9am to 5pm EST
Complete your upgrade
Fits the same truck
Features
- Fits With Your Toolbox: Extang builds the Solid Fold Toolbox 2.0 shorter than the bed so it sits behind a crossover toolbox, and Extang says it works with most 18"-20" toolboxes. You keep full access to the toolbox while the bed behind it stays covered. The toolbox is sold separately.
- L-Channel Toolbox Seal: A patented clamp-on L-channel closes the gap between the toolbox and the cover. Its seal presses against the toolbox so water and road grime stay out of the bed.
- 1" EnduraShield Panels: The panels are 1" EnduraShield TPO in a rigid aluminum frame with a textured-black EnduraCoat finish, made to resist impacts, scrapes and UV fading. Dual-pivot MaxHinges strengthen the joints between panels.
- Tested to OEM Standards, Says Extang: Extang says the cover went through hard testing for water control, load capacity and fade resistance, and that it passes the strictest OEM tests.
- Self-Locking EZ-Lock Clamps: Spring-loaded EZ-Lock clamps at the tailgate lock the cover to the bed flange, or release it so it folds. Folded toward the toolbox and buckled, it opens about two thirds of the bed.
- Off in Seconds: Loosen the Jaw-Grip front clamps by hand and the whole cover lifts off. There are no tools to fit it or take it off, and no holes to drill.
Description & Fitment
The Extang Solid Fold Toolbox 2.0 is a hard folding tonneau cover for the 6'2" bed of the 2015-2022 Chevrolet Colorado / GMC Canyon, sized to sit behind most 18"-20" crossover toolboxes, which are sold separately. An L-channel seal closes the gap between the cover and the toolbox. Its matte-black 1" EnduraShield panels fold and buckle for about two thirds of the bed, and the cover lifts off without tools for full access. Jaw-Grip front clamps and self-locking EZ-Lock rear clamps hold it on with no drilling, and Extang covers it with a three-year warranty.
Fitment & Compatibility
| Years | Model | Bed | Notes |
|---|---|---|---|
| 2015-2022 | Colorado | 6'2" (74") | β |
| Years | Model | Bed | Notes |
|---|---|---|---|
| 2015-2022 | Canyon | 6'2" (74") | β |
Check your bed: measure inside the bed floor from the bulkhead to the inside of the closed tailgate. Extang lists this bed as 6'2"; it measures about 74" (GM calls it the 6'2" Long Box).
Not for: other bed lengths or truck generations; each has its own Solid Fold Toolbox 2.0 part. The crossover toolbox is sold separately; this cover is made to sit behind most 18"-20" crossover toolboxes.
About Extang
Extang is based in Ann Arbor, Michigan, and the Solid Fold Toolbox 2.0 is assembled in Michigan. Extang publishes an install sheet with truck-specific bracket notes and backs the cover with a three-year warranty.
It keeps the panels and frame of Extang's Solid Fold 2.0, shortened to leave room for a crossover toolbox, which is sold separately.
Warranty note. Extang's 3-year limited warranty applies to the original purchaser, with warranty registration on file or a detailed, dated receipt. Keep your order confirmation from us, and contact us for warranty claims and registration help.
Frequently Asked Questions
Will this fit my 2015-2022 Chevrolet Colorado?
Yes, if it has the 6'2" bed. Measure inside the bed floor from the bulkhead to the inside of the closed tailgate: this bed is about 74". Not sure? Send us your VIN and we'll confirm.
How do I measure my bed?
Measure inside the bed floor from the bulkhead to the inside of the closed tailgate. Extang lists this bed as 6'2", about 74" long. Truck makers often round their bed names, so compare the measurement, not the name.
Does it come with a toolbox?
No. The toolbox is sold separately. This cover is made to sit behind a crossover toolbox you already have or buy on its own, and Extang says it fits most 18"-20" crossover toolboxes.
Can I still open my toolbox with the cover on?
Yes. The cover stops at the toolbox, so its lids open as usual, and the L-channel seal along the toolbox keeps water out of the gap between them.
Can I drive with it folded open, or take it off?
Yes to both. Release the rear EZ-Lock clamps and stow them in the rail before you fold the second section, then fold toward the toolbox and fasten both buckle straps for about two thirds of the bed. For the whole bed, loosen the Jaw-Grip front clamps by hand and lift it off. Never drive with it partly open.
How is it different from the regular Solid Fold 2.0?
Extang says it shares the Solid Fold 2.0's construction: 1" EnduraShield panels, an aluminum frame and MaxHinges. The toolbox version is built shorter to leave room for a crossover toolbox and adds the L-channel that seals against it.
Installation
- None for the clamps
- Which tighten by hand
- Cutting tool if a bed cap or liner needs trimming
- Pliers for the stake-pocket nut plates
Here's the short version. Follow Extang's install sheet (below) for your GM truck's exact clamp and bracket hardware. Your crossover toolbox goes in first; it is sold separately.
- Wash the bed and set the L-channel. Wash the truck bed. Stand the L-channel against the toolbox, its foam seal sitting under the L-channel's lower edge on the bed floor, and center it between the bed walls.
- Place the cover. Rest the assembled cover's front rail on top of the L-channel, centered against the toolbox. Unfold it fully and set it for the right cab and tailgate position, then refold it without letting it shift.
- Clear the flange. If a bed cap or bedliner covers the metal bed-wall flange, trim only enough of its edge for every clamp to bite on the bottom of the metal flange.
- Clamp the front. Hook each front clamp under the bed-wall flange and hand-tighten until it touches, then two more turns. Not on the lip of a bedliner or rail cap, and no wrench. Trucks with a factory cargo management rail get a clamp plate at the cab clamps (on most, the tailgate clamps hook straight into the rail), as the sheet's supplement shows.
- Fit the rear brackets, then close it. On this truck the rear of the cover latches to brackets. With pliers, lower a nut plate into each stake pocket (rubber side toward the bed), line the bracket up with the hole in the bed wall and with the cover's spring latch, and screw it through the bed hole into the nut plate, hand-tight; a bedliner needs trimming to reach that hole. With the tailgate open and the front clamps tight, fold the cover out flat and latch it.
- Driving with it folded. Release the rear clamps and stow them securely in the rail before you fold the second section, fold the cover forward toward the toolbox and fasten both straps to the front rail. Clear snow and debris before folding, and never drive with it partly open.
Stuck on a step?
- Solid Fold Toolbox 2.0 cover assembly with Jaw-Grip front and EZ-Lock rear clamps
- L-channel with foam seal
- Buckle straps for driving with the cover folded
- Alternative bracket or clamp-plate hardware for trucks that need it (GM stake-pocket brackets, cargo-rail clamp plates)
- Install guide
Specifications
| Brand | Extang |
|---|---|
| Part Number | EXT84355 |
| Cover Type | Hard tri-fold, toolbox length |
| Toolbox Fit | Most 18"-20" crossover toolboxes (toolbox sold separately) |
| Panels | 1" EnduraShield TPO |
| Frame | Aluminum, textured-black EnduraCoat finish |
| Finish | Matte black |
| Hinges | Dual-pivot MaxHinges |
| Clamps | Jaw-Grip front, EZ-Lock rear (tool-free) |
| Bed Access | About 2/3 folded; full bed with the cover removed |
| Mounting | Clamp-on, no drilling |
| Sealing | L-channel toolbox seal, triple-fin perimeter seals, polymer corner and hinge seals |
| Assembled In | Michigan, USA |
| Bed Length | 6'2" (74") |
| UPC | 750289843552 |
Warranty, shipping & returns
-
Warranty
Extang covers the Solid Fold Toolbox 2.0 for three years from the date of purchase against defects in materials and workmanship.- What's covered: the rails, clamps, bows, aluminum parts and hardware.
- A defective cover or part is repaired or replaced, at Extang's choice; Extang may substitute or offer a warranty discount on a full replacement system, for example when a product is discontinued.
- For the original purchaser, with warranty registration on file or a detailed, dated receipt.
- To keep it valid: clean with Extang Tonno Tonic or soap and water only (no silicone vinyl conditioners); drive only with the cover flat and held at all four clamps, or fully folded and secured with both buckles; never drive with it partly open; keep cargo from touching the panels; clear snow, ice and debris before opening; take the cover off before the truck is towed from the rear.
- Claims: get a return authorization number from Extang first and write it on the outside of the package. Shipping to Extang is at your cost, Extang may ask for the part back postage prepaid, and shipping charges apply to any repair or replacement.
- Not covered: accidents, misuse, neglect, improper service, installation or removal, normal wear and tear, modifications, acts of God, interference with other accessories or trailers, and consequential or incidental damages.
-
Free shipping
Ships free to the lower 48 states, with no minimum order.- Order by 5 PM ET on a business day and it starts processing the same day.
- Because of its size, the cover ships by freight or as an oversized parcel.
- Most orders arrive within 1-5 business days.
- We email your tracking number as soon as it ships.
-
Inspect on delivery
This cover ships in a large, heavy box. The toolbox is not included. Check it as soon as it arrives.- Look for crushed ends, punctures or tears in the carton.
- If something looks wrong, take photos of the box and the parts (and if a driver asks you to sign, note the damage on the receipt).
- Open the box and check the parts against the parts list before you install.
- Email support@prestigetruck.com right away with your order number, a short note and photos. We send a replacement or a full refund at no cost to you.
-
30-day returns
Return it within 30 days of delivery, unused, in the original packaging, with proof of purchase.- Email support@prestigetruck.com with your order number. We reply within 1-2 business days with instructions.
- Damaged, defective or wrong item: we send a prepaid label or arrange a pickup.
- Changed your mind: you pay return shipping. No restocking fee.
- Refunds go back to your original payment method within 7 business days of approval. See our returns policy.