Extang Trifecta 2.0 Soft Folding Tonneau Cover for 2009-2014 Ford F-150 (6'7" Bed, with Cargo Management System)
Free gifts included with your order
- Guaranteed FitmentTeam-confirmed fit or money back
- No Sales TaxZero sales tax on every order
- 30-Day Money-Back GuaranteeReturn it within 30 days of delivery for a refund
Questions or a custom quote?
Mon to Fri, 9am to 5pm EST
Complete your upgrade
Fits the same truck
See it on a truck
Dual-pivot MaxHinges
Triple-fin seals
Leather-grain vinyl top
Features
- Two Thirds of the Bed, Open: Unlatch the two rear clamps and fold the cover up toward the cab, and about two thirds of the bed opens up. Two built-in buckle straps hold it folded so you can drive that way; Extang asks that both straps are buckled and the tethers stay attached, and never a half-open cover on the road.
- Self-Locking Rear Clamps: EZ-Lock clamps at the tailgate end are spring-loaded. They stow in the cover rail, swing down to hook under the bed rail and lock themselves once they're clamped, then release by hand when you want to fold the cover.
- Off in Seconds, No Drilling: Jaw-Grip front clamps hold the cab end with no holes in the truck. When a load needs the whole bed, loosen them by hand and lift the cover out; putting it back on takes no tools either.
- Aluminum Frame, MaxHinges: The frame and support bars are aluminum with a textured black EnduraCoat finish. Every fold turns on a MaxHinge with two pivot points, which Extang uses to strengthen the joints and help them seal.
- Snap-On Triple-Fin Seals: Triple-fin seals snap on, with no adhesive, along the bed rails, bulkhead and tailgate. Extang says they exceed OEM standards, and a damaged seal can be replaced. Like any soft folding cover it resists weather but is not watertight.
- Leather-Grain Vinyl Top: The tarp is heavy-duty leather-grain vinyl with clean, rounded lines and a low profile. A patented corner-tuck system keeps it tight, so it doesn't sag as the temperature swings. Want canvas instead? That's the Trifecta Signature 2.0.
Description & Fitment
The Extang Trifecta 2.0 is a soft tri-fold tonneau cover for the 6'7" bed of the 2009-2014 Ford F-150 with the factory cargo management system. It mounts with a clamp-plate kit made for the factory cargo rails, so there is no drilling. Two buckle straps hold it folded at the cab for about two thirds of the bed, and self-locking rear clamps catch under the rail when you close it. A low-profile leather-grain vinyl top, dual-pivot MaxHinges and snap-on triple-fin seals round it out, backed by Extang's limited lifetime warranty.
Fitment & Compatibility
| Years | Model | Bed | Notes |
|---|---|---|---|
| 2009 | F-150 | 6'7" | Styleside Bed, with Cargo Management System |
| 2010-2014 | F-150 | 6'7" | with Cargo Management System |
Check your bed: measure inside the bed floor from the bulkhead to the inside of the closed tailgate. Extang lists this bed as 6'7". This version is for trucks with the factory cargo management (track) system.
Not for: the 2009-2014 Ford F-150 6'7" bed without the factory cargo management (track) system (92410); the 2009-2014 Ford F-150 5'7" bed (92405); the 2009-2014 Ford F-150 8' bed (92415). Those are separate Trifecta 2.0 parts.
About Extang
Extang is based in Ann Arbor, Michigan. The Trifecta 2.0 is its soft tri-fold cover with a leather-grain vinyl tarp, and the successor to the original Trifecta; Extang publishes a truck-specific install sheet for each version.
The Trifecta 2.0 shares its frame, hinges, clamps and seals with the canvas-topped Trifecta Signature 2.0. Extang also makes the Trifecta Toolbox 2.0 for beds with a crossover toolbox.
Warranty note. Extang's limited lifetime warranty applies to the original purchaser, with warranty registration on file or a detailed, dated receipt. Keep your order confirmation from us, and contact us for warranty claims and registration help.
Frequently Asked Questions
Will this fit my 2009-2014 Ford F-150?
Yes, if it has the 6'7" bed, with the factory cargo management (track) system. Measure inside the bed floor from the bulkhead to the inside of the closed tailgate and compare it with the 6'7" label. If yours is different, look at the 2009-2014 Ford F-150 5'7" bed (92405). Not sure? Send us your VIN and we'll confirm.
Does it matter if my bed has the factory cargo management tracks?
Yes. This version is for beds with the factory cargo management (track) system on the bed rails, and its tethers anchor in those tracks. A bed without the tracks takes the 2009-2014 Ford F-150 6'7" bed without the factory cargo management (track) system (92410).
What is the difference between the Trifecta 2.0 and the Trifecta Signature 2.0?
The tarp. Both share the aluminum frame, MaxHinges, Jaw-Grip and EZ-Lock clamps and the snap-on triple-fin seals. The Trifecta 2.0 uses leather-grain vinyl; the Signature 2.0 swaps it for heavy-duty canvas.
Will it keep rain and snow out of the bed?
It is built to. Snap-on triple-fin seals run along the bed rails, bulkhead and tailgate, and Extang calls the vinyl tarp moisture-resistant. Like every soft folding cover it is weather-resistant rather than watertight. Brush snow and ice off before you fold it; Extang's warranty requires that.
Can I drive with it folded open?
Yes. Stow the rear clamps in the cover rail, fold the cover all the way to the cab and fasten both buckle straps with the tethers attached; about two thirds of the bed is then open. Never drive with it partly folded.
How do I take it off for a big load?
Loosen the Jaw-Grip front clamps by hand and lift the cover out of the bed. No tools are needed to take it off or put it back. Trucks whose sheet adds clamp brackets keep the brackets on.
Installation
- Hand-tightened clamps
- Extang recommends a utility knife and
- For the 65 in-lb bracket screws
- Calibrated torque wrench
Here's the short version. Follow Extang's install sheet (below) for your truck's exact clamp positions and hardware.
- Set the cover in place. Lay the folded cover over the cab end of the bed, unfold it, line it up at the cab and the tailgate, then refold it without moving it. If a plastic bed-rail cap hangs below the metal flange, trim it back with a utility knife so the clamps reach metal; never cut the bed.
- Fit the bracket kit. On a bed with a factory cargo rail system, add the clamp plate, washers and screws to the cab and tailgate clamps as the sheet shows, and torque them to 65 in-lb (7.3 Nm). Don't overtighten.
- Tighten the front clamps. Seat each Jaw-Grip cab clamp under the metal bed flange (not the bedliner lip or a plastic cap) and turn it by hand until it touches, then two more turns. No wrench, and don't overtighten.
- Close it and latch the rear clamps. With the tailgate down and the front clamps tight, unfold the cover fully. Swing each rear clamp down out of the cover rail, slide it at a slight angle as far out toward the bed rail as it goes, then pull it straight down and let go so it hooks under the metal flange. Latch both sides.
- Attach the tethers in the cargo rails. Open the cover and pull the end cap and any tie-down cleats off each cargo rail. Slide the supplied block into the rail, pass the tether knob through its lock washer and the tether bracket into the block, move it up to the front bow and tighten the knob so it can't shift or lift. Refit the cleats and end caps.
- Recheck after a week. Re-tighten the front clamps and tethers after your first week of driving, and check them now and then. To drive folded, stow the rear clamps in the rail before you fold the second section, fold it to the cab and buckle both straps.
Stuck on a step?
- Trifecta 2.0 cover assembly, rear clamps stowed in the cover rails
- Jaw-Grip front (cab) clamps
- Tethers (attached to the cover bow)
- Tether slide blocks for factory cargo-rail beds
Specifications
| Brand | Extang |
|---|---|
| Part Number | EXT92411 |
| Cover Type | Soft tri-fold |
| Tarp | Leather-grain vinyl, corner-tuck system |
| Frame | Aluminum, textured black EnduraCoat finish |
| Finish | Vinyl grain, black |
| Hinges | Dual-pivot MaxHinges |
| Clamps | Jaw-Grip front, spring-loaded EZ-Lock rear |
| Bed Access | About 2/3 folded; full bed with the cover removed |
| Mounting | Clamp-on, no drilling |
| Removal | Tool-free |
| Sealing | Snap-on triple-fin seals |
| Bed Length | 6'7" |
| UPC | 750289924114 |
More media
1 videoWarranty, shipping & returns
-
Warranty
Extang covers the Trifecta 2.0 with a limited lifetime warranty against defects in materials or workmanship, starting from the date of purchase.- What's covered: the rails, aluminum components, clamps, bows, hardware and the vinyl covering.
- A defective cover or part is repaired or replaced, at Extang's choice; for discontinued products Extang may substitute a newer model or offer a warranty discount on a full replacement.
- For the original purchaser only, not transferable. Register the cover with Extang, or keep a detailed, dated receipt; contact us for registration help.
- To keep it valid: clean with Extang Tonno Tonic or mild soap and water (no conditioners that contain silicone or petroleum, which dry out and crack vinyl); keep every clamp fastened when driving closed, or drive fully folded with both buckle straps fastened and both tethers attached; never drive with it partly open; don't let cargo press against the tarp; clear snow, ice and debris before folding; stow the rear clamps before folding the second section; re-tighten the front (cab) clamps and tethers after the first week of driving and check them from time to time after that; take the cover off before the truck is towed from the rear.
- Claims: get a return authorization number from Extang first and write it on the outside of the package. Extang may ask for the part back, postage prepaid, and shipping charges apply to any repair or replacement.
- Not covered: wind-whip damage from an unsecured tarp, accidents, misuse, neglect, improper installation, servicing or removal, normal wear and tear, modifications, acts of God, interference with other accessories or trailers, and consequential or incidental damages.
-
Free shipping
Ships free to the lower 48 states, with no minimum order.- Order by 5 PM ET on a business day and it starts processing the same day.
- Because of its size, the cover ships as an oversized parcel or by freight.
- Most orders arrive within 1-5 business days.
- We email your tracking number as soon as it ships.
-
Inspect on delivery
This cover ships in a large box. Check it as soon as it arrives.- Look for crushed ends, punctures or tears in the carton.
- If something looks wrong, take photos of the box and the parts (and if a driver asks you to sign, note the damage on the receipt).
- Open the box and check the parts against the parts list before you install.
- Email support@prestigetruck.com right away with your order number, a short note and photos. We send a replacement or a full refund at no cost to you.
-
30-day returns
Return it within 30 days of delivery, unused, in the original packaging, with proof of purchase.- Email support@prestigetruck.com with your order number. We reply within 1-2 business days with instructions.
- Damaged, defective or wrong item: we send a prepaid label or arrange a pickup.
- Changed your mind: you pay return shipping. No restocking fee.
- Refunds go back to your original payment method within 7 business days of approval. See our returns policy.