Extang Trifecta Signature 2.0 Soft Folding Tonneau Cover for 2026-2027 Ford Ranger / Ranger Raptor (5'1" Bed)
Free gifts included with your order
- Guaranteed FitmentTeam-confirmed fit or money back
- No Sales TaxZero sales tax on every order
- 30-Day Money-Back GuaranteeReturn it within 30 days of delivery for a refund
Questions or a custom quote?
Mon to Fri, 9am to 5pm EST
Complete your upgrade
Fits the same truck
See it on a truck
Premium canvas top
Features
- Premium Canvas Top: Extang tops the Signature 2.0 with heavy-duty canvas in place of the leather-grain vinyl on the Trifecta 2.0. Extang says the canvas is very durable and less affected by weather, and a patented corner-tuck system keeps the tarp tight in heat or cold.
- Dual-Pivot MaxHinges: Every fold turns on a MaxHinge with two pivot points, which Extang uses to strengthen the joints between sections and help them seal.
- Straps Hold It Open: Fold the cover toward the cab and two built-in buckle straps hold it there, so you can drive with about two thirds of the bed open. Extang's rule: buckle both straps, keep the tethers attached, and never drive with it half open.
- Off in Seconds: When a load needs the whole bed, loosen the Jaw-Grip front clamps by hand and lift the cover out. Putting it on or taking it off needs no tools and no drilling.
- Spring-Loaded Rear Clamps: EZ-Lock clamps at the tailgate end stow in the cover rail, swing down to hook under the bed rail and lock themselves once they're clamped. Release them by hand to fold the cover.
- Snap-On Triple-Fin Seals: Triple-fin seals snap on, with no adhesive, along the bed rails, bulkhead and tailgate. Extang says they exceed OEM standards, and a damaged seal can be replaced. Like any soft folding cover it resists weather but is not watertight.
Description & Fitment
The Extang Trifecta Signature 2.0 Soft Folding Tonneau Cover (94639) fits the 2026-2027 Ford Ranger and Ranger Raptor with the 5'1" bed. It is a soft tri-fold cover with a premium canvas top for owners who want the bed covered but easy to open. Dual-pivot MaxHinges join the three sections, snap-on triple-fin seals guard the edges, and buckle straps hold it folded for about two thirds of the bed. It clamps on with brackets in the bed-cap clip holes, and Extang backs it with a five-year limited warranty.
Fitment & Compatibility
| Years | Model | Bed | Notes |
|---|---|---|---|
| 2026-2027 | Ranger | 5'1" | — |
| 2026-2027 | Ranger Raptor | 5'1" | — |
Check your bed: measure inside the bed floor from the bulkhead to the inside of the closed tailgate. Extang lists this bed as 5'1".
Not for: other bed lengths or truck generations; each has its own Trifecta Signature 2.0 part.
About Extang
Extang is based in Ann Arbor, Michigan. The Trifecta Signature 2.0 is its soft tri-fold cover with a canvas tarp; Extang publishes a truck-specific install sheet for each version.
The Signature 2.0 shares its frame, hinges, clamps and seals with the vinyl Trifecta 2.0. Extang also makes the Trifecta Toolbox 2.0 for beds with a crossover toolbox.
Warranty note. Extang's 5-year limited warranty applies to the original purchaser, with warranty registration on file or a detailed, dated receipt. Keep your order confirmation from us, and contact us for warranty claims and registration help.
Frequently Asked Questions
Will this fit my 2026-2027 Ford Ranger?
Yes, if it has the 5'1" bed. Measure inside the bed floor from the bulkhead to the inside of the closed tailgate and compare it with the 5'1" label. Not sure? Send us your VIN and we'll confirm.
Does it fit the Raptor?
Yes. Extang lists the 2026-2027 Ranger Raptor with this 5'1" bed.
What is the difference between the Trifecta Signature 2.0 and the Trifecta 2.0?
The tarp. Both share the aluminum frame, MaxHinges, Jaw-Grip and EZ-Lock clamps and the snap-on triple-fin seals. The Signature swaps the Trifecta 2.0's leather-grain vinyl for heavy-duty canvas, which Extang says is more durable and less affected by weather.
Will it keep rain and snow out of the bed?
It is built to. Snap-on triple-fin seals run along the bed rails, bulkhead and tailgate. Like every soft folding cover it is weather-resistant rather than watertight. Brush snow and ice off before you fold it; Extang's warranty requires that.
Can I drive with it folded open?
Yes. Stow the rear clamps in the cover rail, fold the cover all the way to the cab and fasten both buckle straps with the tethers attached; about two thirds of the bed is then open. Never drive with it partly folded.
How do I take it off for a big load?
Loosen the Jaw-Grip front clamps by hand and lift the cover out of the bed. No tools are needed to take it off or put it back.
Installation
- T-30 Torx bit
- Isopropyl alcohol
- Utility knife (Extang's TOOLS REQUIRED)
- Calibrated torque wrench for the 8 ft-lb brackets
Here's the short version. Follow Extang's install sheet (below) for your truck's exact clamp positions and hardware.
- Take out the corner clips. Pry the two corner clips out of the driver and passenger bed caps. Keep them; Extang suggests a bag in the glove box.
- Fit the clamp brackets. Where each clip came out, mount a bracket with a T-30 Torx bolt and an M6 nut, with the nut behind the sheet metal. Torque to 8 ft-lb (11 Nm).
- Stick on the bulkhead seal. Wash the top of the bulkhead with soap and water, wipe it with isopropyl alcohol and let it dry. Peel the backing and press the seal on flush with the front edge, snug between the bed rails, pressing along its full length.
- Place the cover and clamp the front. Set the cover over the cab end, centered and square with the bed, without crushing the seals. Hook each cab clamp under the bracket you fitted, turn it by hand until it touches, then two more turns. No wrench.
- Tether, close and square it. Clip each tether to the front tie-down on both sides. With the tailgate open, close the cover; then shut the tailgate, unfold the cover and check that it sits parallel and square, with the bulb seal resting on the tailgate. If not, loosen the cab clamps and move it.
- Latch the rear clamps. Swing each rear clamp down out of the cover rail, slide it at a slight angle out toward the bed rail, then pull it straight down and let go so it hooks under the bracket. Latch both sides.
Stuck on a step?
- Trifecta Signature 2.0 cover assembly
- Bulkhead seal
- 4 clamp brackets
- 4 T-30 Torx bolts
- 4 M6 nuts
Specifications
| Brand | Extang |
|---|---|
| Part Number | EXT94639 |
| Cover Type | Soft tri-fold |
| Tarp | Heavy-duty canvas, corner-tuck system |
| Frame | Aluminum, textured black EnduraCoat finish |
| Finish | Matte black |
| Hinges | Dual-pivot MaxHinges |
| Clamps | Jaw-Grip front, spring-loaded EZ-Lock rear |
| Bed Access | About 2/3 folded; full bed with the cover removed |
| Mounting | Clamp-on, no drilling |
| Removal | Tool-free |
| Sealing | Snap-on triple-fin seals |
| Bed Length | 5'1" |
| UPC | 750289946390 |
More media
1 videoWarranty, shipping & returns
-
Warranty
Extang covers the Trifecta Signature 2.0 against defects in materials or workmanship for five years from the date of purchase.- What's covered: the rails, aluminum components, clamps, bows, hardware and the tarp.
- A defective cover or part is repaired or replaced, at Extang's choice; Extang may substitute a newer model of similar form and function, or offer a warranty discount on a full replacement.
- For the original purchaser only, not transferable. Register the cover with Extang, or keep a detailed, dated receipt; contact us for registration help.
- To keep it valid: clean with Extang Tonno Tonic or mild soap and water (no conditioners that contain silicone or petroleum); keep every clamp fastened when driving closed, or drive fully folded with both buckle straps fastened and both tethers attached; never drive with it partly open; don't let cargo press against the tarp; clear snow, ice and debris before folding; stow the rear clamps before folding the second section; re-tighten the front (cab) clamps and tethers after the first week of driving and check them from time to time after that; take the cover off before the truck is towed from the rear.
- Claims: get a return authorization number from Extang first and write it on the outside of the package. Extang may ask for the part back, postage prepaid, and shipping charges apply to any repair or replacement.
- Not covered: wind-whip damage from an unsecured tarp, accidents, misuse, neglect, improper installation, servicing or removal, normal wear and tear, modifications, acts of God, interference with other accessories or trailers, and consequential or incidental damages.
-
Free shipping
Ships free to the lower 48 states, with no minimum order.- Order by 5 PM ET on a business day and it starts processing the same day.
- Because of its size, the cover ships as an oversized parcel or by freight.
- Most orders arrive within 1-5 business days.
- We email your tracking number as soon as it ships.
-
Inspect on delivery
This cover ships in a large box. Check it as soon as it arrives.- Look for crushed ends, punctures or tears in the carton.
- If something looks wrong, take photos of the box and the parts (and if a driver asks you to sign, note the damage on the receipt).
- Open the box and check the parts against the parts list before you install.
- Email support@prestigetruck.com right away with your order number, a short note and photos. We send a replacement or a full refund at no cost to you.
-
30-day returns
Return it within 30 days of delivery, unused, in the original packaging, with proof of purchase.- Email support@prestigetruck.com with your order number. We reply within 1-2 business days with instructions.
- Damaged, defective or wrong item: we send a prepaid label or arrange a pickup.
- Changed your mind: you pay return shipping. No restocking fee.
- Refunds go back to your original payment method within 7 business days of approval. See our returns policy.