ICON Vehicle Dynamics 2.5 Piggyback Centerline Steering Stabilizer Kit for 2023-2026 Ford F-250/F-350 Super Duty (Front)
Free gifts included with your order
- Guaranteed FitmentTeam-confirmed fit or money back
- No Sales TaxZero sales tax on every order
- 30-Day Money-Back GuaranteeReturn it within 30 days of delivery for a refund
Questions or a custom quote?
Mon to Fri, 9am to 5pm EST
Complete your upgrade
Fits the same truck
Features
- Through-Shaft Centerline Damping: ICON's Centerline stabilizers run the shaft through the body, so damping is equal in both directions and the steering is not pushed or pulled.
- 2.5" Body, Piggyback Reservoir: The 2.5" body and piggyback reservoir add fluid volume against heat fade.
- More Steering Travel: ICON says the kit allows more steering travel than other aftermarket stabilizers.
- Built From 2.5 Series Parts: Internals come from ICON's 2.5 Series shocks, so the stabilizer can be rebuilt.
- Hard Anodized 6061 Body: The 6061 aluminum body is hard anodized.
- ICON Limited Warranty: ICON's published limited warranty applies for the original buyer on the vehicle the part was first installed on. Contact us first and we open the claim with ICON.
Description & Fitment
ICON designed this 2.5 piggyback centerline steering stabilizer kit around the 2023-2026 Ford F-250 Super Duty and F-350 Super Duty, for 4WD models. The through-shaft centerline design removes the push and pull of a conventional stabilizer for a symmetrical steering feel. ICON sizes the body at 2.5" and adds a piggyback reservoir so damping holds up when hot, with extra steering travel too. It shares parts with ICON's 2.5 Series shocks, so it is fully rebuildable, and the body is hard anodized 6061 aluminum.
Fitment & Compatibility
| Years | Model | Bed | Notes |
|---|---|---|---|
| 2023-2026 | F-250 Super Duty | 4WD | |
| 2023-2026 | F-350 Super Duty | 4WD |
Check your fit: match your year, model and the notes in each row: 2023-2026 Ford F-250 Super Duty (4WD); 2023-2026 Ford F-350 Super Duty (4WD).
Not for: years, models or trims outside those rows. Other steering stabilizers in this line for the same models: 36511 (VS 2.0 Aluminum Series Dual Steering Stabilizer, 1999-2026); 65000 (Dual Steering Stabilizer Kit, 2005-2022); 65002 (Dual Steering Stabilizer Bracket Kit, 2023-2026); 65052 (2.5 Piggyback Centerline Steering Stabilizer Kit, 2005-2022); 65054 (2.5 Piggyback Centerline Steering Stabilizer Kit, 2005-2024); 66515 (VS 2.0 Aluminum Series Dual Steering Stabilizer, front and rear, 2008-2016).
About ICON Vehicle Dynamics
ICON Vehicle Dynamics designs and builds performance suspension for trucks and SUVs at its shop in Riverside, California. Engineering is led by Dylan Evans, its head engineer and a SCORE champion driver, and ICON tests its parts on the street, on the trail and under race conditions.
ICON's engineers begin with the result they want from a vehicle, then study the forces acting on it in motion, which is where the name Vehicle Dynamics comes from. Fabrication stays in ICON's own shop, from laser cutting and metal forming to CNC machining, welding and final assembly. ICON calls its suspension systems and shock absorbers the top choice for popular trucks and SUVs.
Authorized ICON Vehicle Dynamics dealer. Prestige Truck is an authorized ICON Vehicle Dynamics dealer, so every ICON part we sell is new and genuine. ICON's warranty is for the original retail buyer, on the vehicle the part was first installed on. Keep your Prestige Truck order receipt: we use it when we take a claim to ICON for you.
Frequently Asked Questions
Will this fit my 2023-2026 Ford F-250 Super Duty?
It fits when your vehicle matches one of these rows: 2023-2026 Ford F-250 Super Duty (4WD); 2023-2026 Ford F-350 Super Duty (4WD). If you are unsure about your trim or drivetrain, send us your VIN and we will check it against ICON's application list before you order.
Where are the install instructions?
Yes. ICON's install sheet for 65053 is linked in the Installation section below, with its steps condensed on this page. Use the sheet for the torque values.
Centerline or conventional stabilizer: what is the difference?
A conventional stabilizer's shaft enters one end, so its gas pressure pushes the steering one way. ICON's Centerline units run the shaft through the body, giving equal damping both ways with no push or pull.
Will a stabilizer fix death wobble?
A stabilizer damps steering shake but does not cure worn or loose front-end parts. Have the track bar, tie rods and ball joints checked if the shake persists.
Do I need a bump stop spacer?
Some ICON stabilizers call for a bump stop spacer of at least 1". The Installation section of each part shows what ICON asks for.
What warranty applies?
ICON covers its shock absorbers, steering stabilizer shocks included, for 1 year against manufacturer's defects, for the original buyer. Contact us first for a claim and we will send it to ICON for inspection.
Installation
- Torque Wrench
- Tape Measure
- 13mm Socket / Wrench
- 3/16" Allen Wrench
- 3/4" Socket / Wrench
Here's the short version. Follow ICON's install sheet (below) for your vehicle's exact steps and torque values.
- Remove the (4) highlighted bolts from the differential cover using a 13MM socket/wrench.
- Install the steering stabilizer bracket over the differential cover using the supplied M8-1.25 bolts. Tighten using a 13MM socket/ wrench. [Torque to factory spec]
- Set the steering stabilizer so there is 4.340" of dead shaft showing.
- Install the steering stabilizer with the rod end side into the bracket using the supplied 1/2" hardware and a 3/4" socket/wrench. [Torque to 80 ft-lbs]
- Install stabilizer clamp onto the tie rod, being sure not to extend or collapse the stabilizer. Make sure steering wheel and tires are straight/centered.
- After installation, cycle steering left and right to ensure full range of steering is achievable and stabilizer is installed correctly.
Stuck on a step?
Specifications
| Brand | ICON Vehicle Dynamics |
|---|---|
| Part Number | 65053 |
| Position | Front |
| Finish | Hard anodized 6061 aluminum body |
| UPC | 840103423876 |
Warranty, shipping & returns
-
Warranty
ICON covers its shock absorbers, steering stabilizer shocks included, for 1 year against manufacturer's defects.- Coverage belongs to the original retail buyer who owns the vehicle the part was first installed on.
- A shock that fails in its first year goes to ICON for inspection and service. If ICON finds the cause was neglect, poor installation or anything other than normal wear and tear, the owner pays for labor, parts and shipping.
- ICON repairs or replaces a defective part, at its discretion. Removal, reinstallation, freight and incidental or consequential costs are not covered, and parts that wear in normal use are not treated as defective.
- Not covered: finish (including finish marks from shipping), alterations or modifications, installation that departs from ICON's instructions, racing use, police, taxi, government or commercial vehicles, and sales outside the United States and Canada.
- ICON shocks leave the factory charged with nitrogen. Letting that charge out can make a shock malfunction, and ICON does not cover a failure caused by low nitrogen pressure.
- To claim, contact us first with your order number and a short description of the problem. We open the claim with ICON for you, and your Prestige Truck receipt is the proof of purchase ICON asks for.
-
Free shipping
Ships free to the lower 48 states, with no minimum order.- Order by 5 PM ET on a business day and it starts processing the same day.
- Most orders arrive within 1-5 business days.
- We email your tracking number as soon as it ships.
-
Inspect on delivery
Check the stabilizer body, shaft, reservoir, brackets and clamps as soon as the carton arrives, and photograph any damage before installation. Check it as soon as it arrives.- Look for crushed ends, punctures or tears in the carton.
- If something looks wrong, take photos of the box and the parts (and if a driver asks you to sign, note the damage on the receipt).
- Open the box and check the parts against the parts list before you install.
- Email support@prestigetruck.com right away with your order number, a short note and photos. We send a replacement or a full refund at no cost to you.
-
30-day returns
Return it within 30 days of delivery, unused, in the original packaging, with proof of purchase.- Email support@prestigetruck.com with your order number. We reply within 1-2 business days with instructions.
- Damaged, defective or wrong item: we send a prepaid label or arrange a pickup.
- Changed your mind: you pay return shipping. No restocking fee.
- Refunds go back to your original payment method within 7 business days of approval. See our returns policy.