Roll-N-Lock A-Series XT Retractable Tonneau Cover for 2022-2026 Toyota Tundra (6'7" Bed)
Free gifts included with your order
- Guaranteed FitmentTeam-confirmed fit or money back
- No Sales TaxZero sales tax on every order
- 30-Day Money-Back GuaranteeReturn it within 30 days of delivery for a refund
Questions or a custom quote?
Mon to Fri, 9am to 5pm EST
Complete your upgrade
Fits the same truck
See it on a truck
Rack-ready T-slot rails
Compact front canister
Clamps on, no rail drilling
Features
- MaxTrak T-slot rails: Roll-N-Lock's MaxTrak system builds two slim T-slot rails into the sides of the cover. Add crossbars (sold separately) and Roll-N-Lock says they accept most T-slot racks and accessories, so the cover can share the truck with bike, kayak or gear mounts. Crossbars and racks are not included.
- Dual-layer aluminum deck: Under the rails is the A-Series deck: two layers of aluminum slats joined by a patented hinge system, finished in a matte black powder coat that Roll-N-Lock says resists corrosion, UV fading and abrasion. There is no vinyl skin to wear.
- Locks with your tailgate: Twist the included key to lock the rear latch, and a cover over the key slot keeps out rain and snow. Once the cover is closed and locked, Roll-N-Lock's patented built-in tailgate locking system keeps a locking tailgate from being opened. Roll-N-Lock's sheets still note that no bed cover prevents theft outright.
- Rolls into a compact canister: A torsion-spring drive rolls the deck into a canister Roll-N-Lock lists at 7.25" deep, at the front of the bed. The integrated pull strap brings it back from outside the bed, and the ratchet-style latch holds it at three positions along the way.
- Drain tubes clear the canister: Hidden seals shed most weather, and two drain tubes carry water that gets past them from the canister to below the truck. Roll-N-Lock's sheets say the cover is not airtight, so keep the drains clear and treat it as weather-resistant, not waterproof.
- Clamps on, no rail drilling: The tracks clamp or bolt on with a truck-specific kit, and Roll-N-Lock notes that installation is the same for the standard and XT tracks. Most trucks still need a 1/2" hole for each drain tube, and a plastic drop-in bedliner has to be cut. Your truck's sheet shows each step.
Description & Fitment
The Roll-N-Lock A-Series XT (part 576A-XT) is an aluminum retractable tonneau cover with MaxTrak T-slot rails for crossbars, made for the 2022-2026 Toyota Tundra with the 6'7" bed. It's for owners who want a lockable hard cover and a rack base in one, though it won't fit trucks with the factory spray-in liner carrying the molded Tundra nameplate or the Trail Edition package. A key twist lets the dual-layer aluminum deck roll into its compact canister, three latch positions let you lock it part-way open, and it locks with your tailgate. The integrated pull strap closes it from outside the bed, and Roll-N-Lock backs it with a 3-year limited warranty.
Fitment & Compatibility
| Years | Model | Bed | Notes |
|---|---|---|---|
| 2022-2026 | Tundra | 6'7" (78.7") | Not compatible with the factory spray-in liner that carries the molded “Tundra” nameplate. Not compatible with the Trail Edition package |
Check your bed: measure along the bed rail from the bulkhead to the inside of the closed tailgate. This part is for the 6'7" bed on the 2022-2026 Toyota Tundra. Measured, that box is about 78.7" long.
Not for: the 5'7" bed (575A-XT) and trucks with the factory spray-in liner that carries the molded “Tundra” nameplate or the Trail Edition package.
About Roll-N-Lock
Roll-N-Lock makes retractable tonneau covers that roll into a canister at the front of the bed, plus the Cargo Manager bed divider that rides in their tracks. Every cover is built for one truck and one bed length.
The range covers the manual M-Series (vinyl over aluminum slats) and A-Series, the electric E-Series (5-year warranty), XT versions with T-slot rails for crossbars and racks, and the Cargo Manager. The M-Series and A-Series carry a 3-year limited warranty. The A-Series XT adds the MaxTrak T-slot rails to the all-aluminum A-Series.
Authorized Roll-N-Lock dealer. Prestige Truck is an authorized Roll-N-Lock dealer, so what we sell is new and genuine Roll-N-Lock. Roll-N-Lock's warranty covers products "purchased directly or from an authorized reseller," and Roll-N-Lock "does not warrant any products purchased from unauthorized resellers." Your Prestige Truck order receipt is your proof of purchase.
Frequently Asked Questions
Will this fit my 2022-2026 Tundra?
Yes, if it has the 6'7" bed, about 78.7" long. Measure along the bed rail from the bulkhead to the inside of the closed tailgate. It is not for the 5'7" bed (575A-XT). It won't fit a truck with the factory spray-in liner that carries the molded “Tundra” nameplate or the Trail Edition package. If you're unsure, send us your VIN and we'll confirm.
Do I have to drill into my truck?
Not into the bed rails. Roll-N-Lock's sheet runs the drain tubes through 1/2" holes drilled at existing holes in the bed floor, and a plastic drop-in bedliner has to be cut. The install sheet for this truck shows each step.
Are crossbars included?
No. The two MaxTrak T-slot rails are built into the cover, but crossbars and racks are sold separately. Roll-N-Lock says the rails accept most T-slot racks and accessories; tell us which rack you have and we'll check it with Roll-N-Lock before you order.
How is it different from the regular A-Series?
It's the same all-aluminum retractable, with the same 7.25" canister, keyed latch and tailgate lock, plus two MaxTrak T-slot rails along the sides. Roll-N-Lock's install sheets note that installation is the same for the standard track and the XT track.
Is it waterproof?
No, and Roll-N-Lock doesn't claim it is. Hidden seals shed rain and snow and drain tubes carry off water that gets past them, but Roll-N-Lock's sheets say the cover is not airtight and its warranty excludes water intrusion. Keep the drains and the canister clear of debris.
Is it safe to be in the bed with the cover closed?
No. Roll-N-Lock warns that the cover has no release inside the bed, so never let anyone ride or climb in the bed while it's closed. Don't put anything on top of the cover when opening or closing it, and use the pull strap only for opening and closing, never to climb in or out.
Installation
- Jig saw
- 1/2" drill bit
- Drill with Phillips head
- Phillips screwdriver
- Tape measure
Here's the short version. Follow Roll-N-Lock's install sheet (below) for your truck's exact measurements, hardware and part letters.
- Prep the bed. Remove the factory rail channels at the bulkhead and on both sides, and lift the lid off the housing.
- Seal and drill. Press a butyl strip into the seam on each side, then drill a 1/2" hole through the existing hole in the bed floor on each side for the drain tubes.
- Fit the L brackets. Screw the Tundra L brackets into the pre-drilled holes with the 6mm x 25mm pan head screws and 1/4" flat washers (two or three per side, by bed length).
- Seat the tracks. Turn the lock to 10 o'clock (leave the wing nut on), seat the tracks on the housing stems, then close the tailgate and slide the housing back until the tracks touch it.
- Set the spacing and tighten. Set the inside track-to-track width to 59 7/16" with the cargo shield notches and keep 1/8" at the tailgate. Line each angle up with its L bracket, shim any gap, then tighten the L brackets to the track clamps with the 5/16" x 3/4" socket cap screws and the 1/4" Allen, without over-tightening.
- Close it and run the drains. Turn the lock to 7 o'clock, discard the plastic wing nut, pull the cover back and refit the lid with its two lid screws. Feed the drain tubes through the floor holes toward the ground and onto the housing fittings, clear of the cab vents, and clip the pull strap to a rear tie-down.
Stuck on a step?
- Housing (1)
- Track (2)
- Cargo shield (1)
- Drain tube (2)
- Tundra "L" bracket (4; 6 with the 6.5 ft bed)
- 1" x 2" x 1/4" Threaded block (4; 6 with the 6.5 ft bed)
- #10-24 Screw (2)
- Cargo nut (2)
- 5/16" Lock washer (4; 6 with the 6.5 ft bed)
- 5/16" x 1" Cap screw (4; 6 with the 6.5 ft bed)
- 1/4-20 x 1-1/4" Flat head black screw (4; 6 with the 6.5 ft bed)
- 6m x 25mm Pan head screw (4; 6 with the 6.5 ft bed)
- 1/4-20 Lid screw (Taped to lid) (2)
- Black rubber washer (4)
- 1/4-20 x 3/8" Screw (4)
- Shim (4; 6 with the 6.5 ft bed)
- 5/16" x 3/4" Cap screw (5; 6 with the 6.5 ft bed), 2022+ trucks
- Shim (4; 6 with the 6.5 ft bed), 2022+ trucks
- 1/4" Flat washer (4; 6 with the 6.5 ft bed), 2022+ trucks
- Butyl caulk strip (4), 2022+ trucks
- Tundra "L" bracket (4; 6 with the 6.5 ft bed), 2022+ trucks
- 303 Vinyl protector
Specifications
| Brand | Roll-N-Lock |
|---|---|
| Part Number | ROL576A-XT |
| Series | A-Series XT |
| Cover Type | Manual retractable with T-slot rails |
| Construction | Dual-layer aluminum slats, patented hinge system |
| Rails | MaxTrak system, two T-slot rails |
| Crossbars and Racks | Not included |
| Finish | Matte black powder coat |
| Canister Depth | 7.25" |
| Latch | Keyed twist-lock with key-slot cover |
| Latch Positions | 3 (patented ratchet-style latch) |
| Opening | Torsion-spring drive; integrated pull strap |
| Tailgate Lock | Built-in tailgate locking system (needs a locking tailgate) |
| Mounting | Truck-specific clamp or bracket kit; see the install sheet |
| Bed Length | 6'7" (78.7") |
Warranty, shipping & returns
-
Warranty
Roll-N-Lock warrants the A-Series XT against defects in materials and workmanship for three (3) years from the date of purchase.- A part found defective from the manufacturing process is repaired or replaced at no charge, at Roll-N-Lock's option, and Roll-N-Lock may substitute a newer model of similar form and function. Labor to remove or reinstall the cover is not covered.
- It covers the original purchaser only and is not transferable. It ends if the cover is moved to another vehicle or the truck changes owners. Keep your proof of purchase; contact us for help with registration or a claim.
- To keep it valid: clean with mild automotive soap and water only, no strong chemicals; never use silicone or petroleum lubricants on the rails or in the tracks; keep the cover latched and the tether strap secured while driving; check every clamp and mount for tightness after the first week and now and then after that; clear snow and ice off before opening; take the cover off before the truck is towed from the rear.
- Claims: Roll-N-Lock issues a Return Material Authorization (RMA) number before anything is returned, and may ask for the defective part back, packaged and shipped at your expense, with the product ID and a short description of the problem.
- Not covered: improper installation; use below -30°F or above 120°F; water intrusion, including leaks from normal use; misuse, modification or tampering; improper maintenance; use outside the product specifications; normal wear, cosmetic damage or finish fading from sun or chemicals; negligence; accidents, flood, fire and other acts of God; parts not made by Roll-N-Lock.
-
Free shipping
Ships free to the lower 48 states, with no minimum order.- Order by 5 PM ET on a business day and it starts processing the same day.
- This cover is an oversized item, so it ships by freight or as an oversized parcel.
- Most orders arrive within 1-5 business days.
- We email your tracking number as soon as it ships.
-
Inspect on delivery
This cover ships in a long, heavy box. Check it as soon as it arrives.- Look for crushed ends, punctures or tears in the carton.
- If something looks wrong, take photos of the box and the parts (and if a driver asks you to sign, note the damage on the receipt).
- Open the box and check the parts against the parts list before you install.
- Email support@prestigetruck.com right away with your order number, a short note and photos. We send a replacement or a full refund at no cost to you.
-
30-day returns
Return it within 30 days of delivery, unused, in the original packaging, with proof of purchase.- Email support@prestigetruck.com with your order number. We reply within 1-2 business days with instructions.
- Damaged, defective or wrong item: we send a prepaid label or arrange a pickup.
- Changed your mind: you pay return shipping. No restocking fee.
- Refunds go back to your original payment method within 7 business days of approval. See our returns policy.